What 15.1 gpg means for a home in Round Rock
Of the 10 cities in our directory so far, Round Rock ranks #4 for hardness, harder than 67% of them. Its water carries about 1.3× the minerals of the directory median (196 mg/L). A three-person household using typical amounts sends roughly 177.0 lb of dissolved hardness minerals a year through its pipes and appliances. Some of that ends up as scale anywhere the water is heated or left to evaporate.
Round Rock's report contains two averages: 258 ppm in the data table and 249 mg/L (14.55 gpg) in the text. Either way the water is very hard. We use the table figure because it sits next to the published range, and for sizing we also show the 358 ppm peak.
The 100 to 358 ppm range is wider than in most cities in this directory. It reflects a system that blends lake water with Edwards Aquifer groundwater, and limestone aquifer water is typically much harder than reservoir water.
The city's position is worth knowing: the report says plumbing does not need to be softened and describes this hardness as causing aesthetic problems such as spots. That is fair for pipes, but water heaters, tankless units and espresso machines are a different story. Their manufacturers set hardness limits, and Round Rock's average is above most of them.
Where the water comes from: Surface water mainly from Lake Georgetown, plus Lake Travis water treated by the Brushy Creek Regional Utility Authority, and groundwater from the Edwards Aquifer.
What size water softener for Round Rock?
The table assumes 75 gallons per person per day and one regeneration about every seven days at a salt-efficient setting. Because Round Rock's published figure is a range, the recommended sizes use the top of the range (20.9 gpg). The last column shows what the annual average (15.1 gpg) alone would suggest. A softener sized for the peak just regenerates a little less often when the water is softer.
| Household | Grains / day | Recommended size | Regenerates every | At 15.1 gpg (average) |
|---|---|---|---|---|
| 1 person | 1,570 | 24,000 | 10 days | 24,000 |
| 2 people | 3,140 | 40,000 | 8 days | 24,000 |
| 3 people | 4,711 | 64,000 | 9 days | 40,000 |
| 4 people | 6,281 | 80,000 | 8 days | 48,000 |
| 5 people | 7,851 | 96,000 | 8 days | 64,000 |
Sizes are rated grain capacities of common residential units. If you also have iron, or use far more water than average, use the calculator below. Method.
Sized for one regeneration roughly every 7 days, assuming a salt-efficient setting delivers about two thirds of a unit's rated capacity. How we calculate this.
Protecting appliances at 15.1 gpg
- Tank water heaters: drain a few gallons from the bottom valve every six months. At over 15 gpg the sediment layer builds fast, and you'll hear it as popping or rumbling when the burner runs. Check the anode rod every two to three years.
- Tankless heaters: check the manual's hardness limit before anything else. Most units at this hardness need either a softener or an inline scale inhibitor, plus a vinegar or descaler flush of the heat exchanger at the interval the maker specifies.
- Dishwashers: if yours has a built-in softener (common on European brands), set it for about 21 gpg (20 °dH) and keep the salt topped up. Otherwise use rinse aid and a citric-acid cleaning cycle once a month.
- Coffee and espresso machines: descale monthly, or use filtered or softened water in the reservoir. Espresso boilers are the most expensive scale casualty in very hard-water homes.
- Showerheads and aerators: soak them in white vinegar for an hour when the spray pattern starts to break up. Expect to do this every couple of months.
Testing and treatment options
Disclosure: some links below are affiliate links. If you buy through them, Hardness Index may earn a commission at no extra cost to you. It never changes the data on this page. Details.
Hardness test strips
A few dollars to confirm the utility figure at your own tap before you size anything. Look for strips that read in gpg up to at least 25.
See test strips AFFILIATE_LINK_AMAZON_TEST_STRIPSSalt-based softener, 80k grain
The size we'd pick for a family of four in Round Rock. Choose a metered (demand-initiated) valve so it regenerates by use, not by the calendar.
Compare softeners AFFILIATE_LINK_SPRINGWELLSalt-free scale conditioner
Template-assisted crystallization (TAC) units reduce scale on heaters without removing minerals. They won't stop spotting on glass and are less proven above about 25 gpg.
See conditioners AFFILIATE_LINK_AQUASANAWhere this number comes from
- Publisher
- City of Round Rock
- Water system
- City of Round Rock Utilities & Environmental Services
- Data period
- Dated June 12, 2026; 2025 calendar-year data
- Figure type
- Annual average (with published range)
- Accessed
- November 18, 2026
- URL
- roundrocktexas.gov
- ZIP codes
- 78664, 78665, 78680, 78681, 78682, 78683 (postal city “Round Rock”. Utility boundaries may differ.)
“2025 Hardness High 358 Low 100 Average 258 ppm. Elsewhere in the report: "The average water hardness in Round Rock is 249 mg/L or approximately 14.55 grains per gallon."”
Round Rock water hardness: common questions
Is Round Rock water hard?
Yes. At 258 mg/L (15.1 gpg) it is very hard by the USGS definition, which starts at 181 mg/L. The figure comes from City of Round Rock (Dated June 12, 2026).
What should I set my water softener to in Round Rock?
Start at 21 gpg, the top of the published range. If you still see spots on glassware after a couple of weeks, raise it by 2 gpg. A test strip on softened water should read 0–1 gpg.
What size softener does a family of four need?
About 6,281 grains a day, so a 80,000-grain unit regenerating roughly every 8 days.
Does this apply if I'm on a private well?
No. Private wells around Round Rock draw from different depths and formations and can measure very differently. Test the well directly. A lab test also checks iron, which affects softener sizing.