What 15.6 gpg means for a home in Pflugerville
Of the 10 cities in our directory so far, Pflugerville ranks #3 for hardness, harder than 78% of them. Its water carries about 1.4× the minerals of the directory median (196 mg/L). A three-person household using typical amounts sends roughly 183.2 lb of dissolved hardness minerals a year through its pipes and appliances. Some of that ends up as scale anywhere the water is heated or left to evaporate.
Pflugerville does not publish an average, only a low of 201 and a high of 333 mg/L. That spread is wide enough to change the softener you buy: 11.8 gpg at the low end, 19.5 gpg at the high end. Size for the high figure; a softener that is slightly oversized just regenerates less often.
The spread makes sense given the supply mix. Lake water and groundwater rarely carry the same mineral load, and the report also includes Manville WSC's own table, which lists total hardness as CaCO3 from 39.7 to 346 ppm. Homes nearer the Manville interconnect or the city wells may see different water from week to week.
If you run a tankless water heater, check its manual for a hardness ceiling. Manufacturers commonly ask for softening or a scale-inhibiting cartridge well below 19 gpg, and scale damage is a routine warranty exclusion.
Where the water comes from: Lake Pflugerville (fed from the Highland Lakes via Lake Buchanan) is the primary supply, supplemented by two city groundwater wells and a treated-water interconnect with Manville Water Supply Corporation.
What size water softener for Pflugerville?
The table assumes 75 gallons per person per day and one regeneration about every seven days at a salt-efficient setting. Because Pflugerville's published figure is a range, the recommended sizes use the top of the range (19.5 gpg). The last column shows what the midpoint of the published range (15.6 gpg) alone would suggest. A softener sized for the peak just regenerates a little less often when the water is softer.
| Household | Grains / day | Recommended size | Regenerates every | At 15.6 gpg (midpoint) |
|---|---|---|---|---|
| 1 person | 1,461 | 24,000 | 10 days | 24,000 |
| 2 people | 2,921 | 32,000 | 7 days | 32,000 |
| 3 people | 4,382 | 48,000 | 7 days | 40,000 |
| 4 people | 5,842 | 64,000 | 7 days | 64,000 |
| 5 people | 7,303 | 80,000 | 7 days | 64,000 |
Sizes are rated grain capacities of common residential units. If you also have iron, or use far more water than average, use the calculator below. Method.
Sized for one regeneration roughly every 7 days, assuming a salt-efficient setting delivers about two thirds of a unit's rated capacity. How we calculate this.
Protecting appliances at 15.6 gpg
- Tank water heaters: drain a few gallons from the bottom valve every six months. At over 16 gpg the sediment layer builds fast, and you'll hear it as popping or rumbling when the burner runs. Check the anode rod every two to three years.
- Tankless heaters: check the manual's hardness limit before anything else. Most units at this hardness need either a softener or an inline scale inhibitor, plus a vinegar or descaler flush of the heat exchanger at the interval the maker specifies.
- Dishwashers: if yours has a built-in softener (common on European brands), set it for about 19 gpg (19 °dH) and keep the salt topped up. Otherwise use rinse aid and a citric-acid cleaning cycle once a month.
- Coffee and espresso machines: descale monthly, or use filtered or softened water in the reservoir. Espresso boilers are the most expensive scale casualty in very hard-water homes.
- Showerheads and aerators: soak them in white vinegar for an hour when the spray pattern starts to break up. Expect to do this every couple of months.
Testing and treatment options
Disclosure: some links below are affiliate links. If you buy through them, Hardness Index may earn a commission at no extra cost to you. It never changes the data on this page. Details.
Hardness test strips
A few dollars to confirm the utility figure at your own tap before you size anything. Look for strips that read in gpg up to at least 25.
See test strips AFFILIATE_LINK_AMAZON_TEST_STRIPSSalt-based softener, 64k grain
The size we'd pick for a family of four in Pflugerville. Choose a metered (demand-initiated) valve so it regenerates by use, not by the calendar.
Compare softeners AFFILIATE_LINK_SPRINGWELLSalt-free scale conditioner
Template-assisted crystallization (TAC) units reduce scale on heaters without removing minerals. They won't stop spotting on glass and are less proven above about 25 gpg.
See conditioners AFFILIATE_LINK_AQUASANAWhere this number comes from
- Publisher
- City of Pflugerville
- Water system
- City of Pflugerville Public Works · PWS ID TX2270014
- Data period
- Published July 1, 2026; 2025 calendar-year data
- Figure type
- Published range (no average published)
- Accessed
- November 18, 2026
- URL
- content.civicplus.com
- ZIP codes
- 78660, 78691 (postal city “Pflugerville”. Utility boundaries may differ.)
“Hardness (CACO3) Mg/L Low 201 High 333 ... Hardness; deposits”
Pflugerville water hardness: common questions
Is Pflugerville water hard?
Yes. At 267 mg/L (15.6 gpg) it is very hard by the USGS definition, which starts at 181 mg/L. The figure comes from City of Pflugerville (Published July 1, 2026).
What should I set my water softener to in Pflugerville?
Start at 19 gpg, the top of the published range. If you still see spots on glassware after a couple of weeks, raise it by 2 gpg. A test strip on softened water should read 0–1 gpg.
What size softener does a family of four need?
About 5,842 grains a day, so a 64,000-grain unit regenerating roughly every 7 days.
Does this apply if I'm on a private well?
No. Private wells around Pflugerville draw from different depths and formations and can measure very differently. Test the well directly. A lab test also checks iron, which affects softener sizing.