Water hardness in Fargo, ND

City of Fargo Water Treatment Plant reports annual average hardness of 134 mg/L, which is 7.8 grains per gallon. On the USGS scale, that is hard water.

Last verified against the source on November 18, 2026 · View source

Annual average
7.8gpgHard
134 mg/L as CaCO₃
Published range
Not published
Softener setting
8 gpg
Family of 4 needs
32,000 grain
Data period
Approved June 5, 2026
Source: City of FargoAccessed 2026-11-18
What the number means

What 7.8 gpg means for a home in Fargo

Of the 10 cities in our directory so far, Fargo ranks #8 for hardness, harder than 22% of them. That is well below the directory median of 196 mg/L. A three-person household using typical amounts sends roughly 91.9 lb of dissolved hardness minerals a year through its pipes and appliances. Some of that ends up as scale anywhere the water is heated or left to evaporate.

Fargo runs a lime softening plant, so the 134 mg/L that reaches homes is far lower than the river water coming in. The previous year's report listed 120 ppm (7 gpg), so the 2025 average moved up by about 14 ppm. Small year-to-year shifts like this are normal for a river supply.

At about 7.8 gpg, Fargo is at the low end of 'hard'. Many households here skip a whole-house softener and descale appliances instead. If you do install one, set it to the published grains-per-gallon figure rather than the factory default, which is often 20 or more and wastes salt.

Fargo's water leaves the plant at a high pH (the report's aesthetic average is 9.20). That is typical after lime softening and is one reason the white film on glassware here tends to be thin and powdery rather than crusty.

Where the water comes from: The Red River is the primary source, with the Sheyenne River (backed by Lake Ashtabula) as an alternative supply. The utility softens the water centrally before it reaches homes.

Softener sizing

What size water softener for Fargo?

The table assumes 75 gallons per person per day and one regeneration about every seven days at a salt-efficient setting.

HouseholdGrains / dayRecommended sizeRegenerates every
1 person58824,00014+ days
2 people1,17524,00013 days
3 people1,76324,0009 days
4 people2,35132,0009 days
5 people2,93932,0007 days

Sizes are rated grain capacities of common residential units. If you also have iron, or use far more water than average, use the calculator below. Method.

Pre-filled with Fargo's design value (134 mg/L).
People in the home
4
Mostly relevant for well water. Each 1 ppm adds about 4 gpg of softener load.
Recommended rated capacity
–
Hardness–
Compensated hardness–
Grains removed per day–
Weekly load–
Regenerates about every–
Minerals kept out of pipes / yr–

Sized for one regeneration roughly every 7 days, assuming a salt-efficient setting delivers about two thirds of a unit's rated capacity. How we calculate this.

Limescale & appliances

Protecting appliances at 7.8 gpg

  • Tank water heaters: flush sediment once a year. Scale insulates the bottom of the tank, so the burner or element runs longer for the same hot water.
  • Tankless heaters: 7.8 gpg is near or above the limit many manufacturers set. Plan an annual descaling flush, or fit a scale inhibitor if you're not softening.
  • Dishwashers: use rinse aid. On models with a hardness dial, set it to about 8 gpg (8 °dH). Cloudy glasses mean the setting is too low.
  • Kettles and coffee makers: descale every four to six weeks with citric acid or a commercial descaler.
  • Fixtures: wipe glass shower doors after use. Hard-water spots etch glass if they are left for months.
Equipment

Testing and treatment options

Disclosure: some links below are affiliate links. If you buy through them, Hardness Index may earn a commission at no extra cost to you. It never changes the data on this page. Details.

Step 1 · Confirm

Hardness test strips

A few dollars to confirm the utility figure at your own tap before you size anything. Look for strips that read in gpg up to at least 25.

See test strips AFFILIATE_LINK_AMAZON_TEST_STRIPS
Step 2 · Treat

Salt-based softener, 32k grain

The size we'd pick for a family of four in Fargo. Choose a metered (demand-initiated) valve so it regenerates by use, not by the calendar.

Compare softeners AFFILIATE_LINK_SPRINGWELL
Alternative

Salt-free scale conditioner

Template-assisted crystallization (TAC) units reduce scale on heaters without removing minerals. They won't stop spotting on glass and are less proven above about 25 gpg.

See conditioners AFFILIATE_LINK_AQUASANA
Source & method

Where this number comes from

2025 Water Quality ReportOpen source ↗
Publisher
City of Fargo
Water system
City of Fargo Water Treatment Plant
Data period
Approved June 5, 2026; water quality aesthetic averages for 2025
Figure type
Annual average
Accessed
November 18, 2026
URL
download.fargond.gov
ZIP codes
58102, 58103, 58104, 58105, 58106, 58107, 58108, 58109, 58121, 58122, 58124, 58125, 58126 (postal city “Fargo”. Utility boundaries may differ.)
“WATER QUALITY AESTHETIC AVERAGES FOR 2025 — Total Hardness 134 (ppm) or 7.83 grains/gallon”
Read this before you buy equipment. This is a utility-level figure for the public water system, not a measurement at your tap, and it does not apply to private wells. Grains-per-gallon values are our conversion at 17.1 mg/L per gpg unless the utility published its own. Hardness is an aesthetic and maintenance issue, not a measure of whether water is safe to drink; for that, read the utility's full report.
FAQ

Fargo water hardness: common questions

Is Fargo water hard?

Yes. At 134 mg/L (7.8 gpg) it is hard by the USGS definition. The figure comes from City of Fargo (Approved June 5, 2026).

What should I set my water softener to in Fargo?

Start at 8 gpg. If you still see spots on glassware after a couple of weeks, raise it by 2 gpg. A test strip on softened water should read 0–1 gpg.

What size softener does a family of four need?

About 2,351 grains a day, so a 32,000-grain unit regenerating roughly every 9 days.

Does this apply if I'm on a private well?

No. Private wells around Fargo draw from different depths and formations and can measure very differently. Test the well directly. A lab test also checks iron, which affects softener sizing.