Water hardness in Bismarck, ND

City of Bismarck Water Treatment Facility reports annual average hardness of 124 mg/L, which is 7.3 grains per gallon. On the USGS scale, that is hard water.

Last verified against the source on November 18, 2026 · View source

Annual average
7.3gpgHard
124 mg/L as CaCO₃
Published range
Not published
Softener setting
7 gpg
Family of 4 needs
24,000 grain
Data period
2025 calendar-year report
Source: City of BismarckAccessed 2026-11-18
What the number means

What 7.3 gpg means for a home in Bismarck

Of the 10 cities in our directory so far, Bismarck ranks #9 for hardness, harder than 11% of them. That is well below the directory median of 196 mg/L. A three-person household using typical amounts sends roughly 85.1 lb of dissolved hardness minerals a year through its pipes and appliances. Some of that ends up as scale anywhere the water is heated or left to evaporate.

Bismarck publishes two figures, and the difference matters. 124 mg/L is the annual average. 151 ppm is a single compliance sample taken on March 10, 2025. A one-day sample can't tell you what flows from your tap all year, so we use the average. Its high point does show that Bismarck water can move into the middle of the 'hard' band.

Bismarck's supply is Missouri River water drawn through riverbank sand rather than a deep aquifer, so some drift through the year is plausible. The utility publishes only the annual average and one dated sample, though, so if your kettle seems to scale faster in certain months, a $10 test-strip check will confirm it better than any published figure.

At about 7.3 gpg, a softener is a convenience rather than a necessity for most homes. The appliances that gain the most from one are tankless water heaters and espresso machines.

Where the water comes from: A horizontal collector well next to the Missouri River, drawing from 80 feet down in an aquifer recharged directly by the river. A direct river intake serves as backup.

Softener sizing

What size water softener for Bismarck?

The table assumes 75 gallons per person per day and one regeneration about every seven days at a salt-efficient setting.

HouseholdGrains / dayRecommended sizeRegenerates every
1 person54424,00014+ days
2 people1,08824,00014+ days
3 people1,63224,0009 days
4 people2,17524,0007 days
5 people2,71932,0007 days

Sizes are rated grain capacities of common residential units. If you also have iron, or use far more water than average, use the calculator below. Method.

Pre-filled with Bismarck's design value (124 mg/L).
People in the home
4
Mostly relevant for well water. Each 1 ppm adds about 4 gpg of softener load.
Recommended rated capacity
–
Hardness–
Compensated hardness–
Grains removed per day–
Weekly load–
Regenerates about every–
Minerals kept out of pipes / yr–

Sized for one regeneration roughly every 7 days, assuming a salt-efficient setting delivers about two thirds of a unit's rated capacity. How we calculate this.

Limescale & appliances

Protecting appliances at 7.3 gpg

  • Tank water heaters: flush sediment once a year. Scale insulates the bottom of the tank, so the burner or element runs longer for the same hot water.
  • Tankless heaters: 7.3 gpg is near or above the limit many manufacturers set. Plan an annual descaling flush, or fit a scale inhibitor if you're not softening.
  • Dishwashers: use rinse aid. On models with a hardness dial, set it to about 7 gpg (7 °dH). Cloudy glasses mean the setting is too low.
  • Kettles and coffee makers: descale every four to six weeks with citric acid or a commercial descaler.
  • Fixtures: wipe glass shower doors after use. Hard-water spots etch glass if they are left for months.
Equipment

Testing and treatment options

Disclosure: some links below are affiliate links. If you buy through them, Hardness Index may earn a commission at no extra cost to you. It never changes the data on this page. Details.

Step 1 · Confirm

Hardness test strips

A few dollars to confirm the utility figure at your own tap before you size anything. Look for strips that read in gpg up to at least 25.

See test strips AFFILIATE_LINK_AMAZON_TEST_STRIPS
Step 2 · Treat

Salt-based softener, 24k grain

The size we'd pick for a family of four in Bismarck. Choose a metered (demand-initiated) valve so it regenerates by use, not by the calendar.

Compare softeners AFFILIATE_LINK_SPRINGWELL
Alternative

Salt-free scale conditioner

Template-assisted crystallization (TAC) units reduce scale on heaters without removing minerals. They won't stop spotting on glass and are less proven above about 25 gpg.

See conditioners AFFILIATE_LINK_AQUASANA
Source & method

Where this number comes from

2025 Annual Water Quality ReportOpen source ↗
Publisher
City of Bismarck
Water system
City of Bismarck Water Treatment Facility
Data period
2025 calendar-year report
Figure type
Annual average
Accessed
November 18, 2026
URL
bismarcknd.gov
ZIP codes
58501, 58502, 58503, 58504, 58505, 58506, 58507 (postal city “Bismarck”. Utility boundaries may differ.)
“Average Total Hardness 124 mg/l or 7.3 grains/gallon. (Compliance table: Hardness, total (as CACO3), 3/10/2025, 151 ppm.)”
Read this before you buy equipment. This is a utility-level figure for the public water system, not a measurement at your tap, and it does not apply to private wells. Grains-per-gallon values are our conversion at 17.1 mg/L per gpg unless the utility published its own. Hardness is an aesthetic and maintenance issue, not a measure of whether water is safe to drink; for that, read the utility's full report.
FAQ

Bismarck water hardness: common questions

Is Bismarck water hard?

Yes. At 124 mg/L (7.3 gpg) it is hard by the USGS definition. The figure comes from City of Bismarck (2025 calendar-year report).

What should I set my water softener to in Bismarck?

Start at 7 gpg. If you still see spots on glassware after a couple of weeks, raise it by 2 gpg. A test strip on softened water should read 0–1 gpg.

What size softener does a family of four need?

About 2,175 grains a day, so a 24,000-grain unit regenerating roughly every 7 days.

Does this apply if I'm on a private well?

No. Private wells around Bismarck draw from different depths and formations and can measure very differently. Test the well directly. A lab test also checks iron, which affects softener sizing.